Thanks Scott,
I did do that initially, but maybe your right. I keep
forgetting to redo that after I try resetting the CMOS
serial settings. Maybe that is why I get a modem
ready, but no reply.
michael-
--- Scott Piper <piper@ij.net> wrote:
> Michael, you have to use the setserial options that
> you found in
> /proc/pci, so in your example it would be
>
> setserial /dev/modem uart 16550A port 0xb800 irq 3
>
> or whatever the pci output was.
>
> scott
>
>
>
>
> Michael Ritenour wrote:
>
> >I have followed the instructions that are detailed
> >below, and also tryed using kppp with no luck. Can
> >anyone give me some tips.
> >
> >On my CMOS setting, I have no way of disabling my
> >COM2, but I did try just changing my serial port
> >designation in CMOS.
> >
> >I can see the modem, when I do a cat /proc/pci
> >
> >Anyway, here are some instructions I found online,
> but
> >haven't had luck with them.
> >
> >After physically installing your PCI modem enter
> your
> >CMOS setup and disable COM2 (Serial Port Boot into
> >Linux and log in as root. Then run:
> >
> >cat /proc/pci
> >
> >Look at the output and locate the "bus" entry for
> your
> >modem. You need to locate the IRQ and the base I/O
> >address for the modem. Here is an example of the
> modem
> >output:
> >
> >Non-prefetchable 32 bit memory at 0x00000000.
> >
> >Bus 0, device 17, function 0:
> >Communication controller: Unknown vendor Unknown
> >device (rev 0).
> >Vendor id=1ac1. Device id=480.
> >Medium devsel. Fast back-to-back capable. IRQ 3.
> >Master Capable.
> >No bursts.
> >Min Gnt=252.Max Lat=14
> >Non-prefetchable 32 bit memory at 0xe4000000.
> >I/O at 0xb800 [0xb801]
> >Note in the output above the IRQ is 3 and the base
> I/O
> >is 0xb800. This is common for 56K PCI modem with
> COM2
> >disabled. Now link the modem to COM2 (/dev/ttyS1):
> >
> >ln -s /dev/ttyS1 /dev/modem
> >
> >Add this line to your /etc/rc.d/rc.local file using
> >the IRQ and base I/O address:
> >
> >setserial /dev/modem uart 16550A port 0x6400 irq 11
> >
> >Then run rc.local:
> >
> >. /etc/rc.d/rc.local
> >
> >You can test your modem by running "minicom" at the
> >command prompt. For example type ATDT18006381483 to
> >dial the phone number. The modem should dial this
> >number. "CTRL-A Q" will quit minicom.
> >
> >thanks in advance,
> >
> >michael ritenour
> >
> >
>
>-----------------------------------------------------------------------
> >This list is provided as an unmoderated internet
> service by Networked
> >Knowledge Systems (NKS). Views and opinions
> expressed in messages
> >posted are those of the author and do not
> necessarily reflect the
> >official policy or position of NKS or any of its
> employees.
> >
> >
> >
>
>
>
-----------------------------------------------------------------------
> This list is provided as an unmoderated internet
> service by Networked
> Knowledge Systems (NKS). Views and opinions
> expressed in messages
> posted are those of the author and do not
> necessarily reflect the
> official policy or position of NKS or any of its employees.
-----------------------------------------------------------------------
This list is provided as an unmoderated internet service by Networked
Knowledge Systems (NKS). Views and opinions expressed in messages
posted are those of the author and do not necessarily reflect the
official policy or position of NKS or any of its employees.
This archive was generated by hypermail 2.1.3 : Fri Aug 01 2014 - 20:03:57 EDT